My 2006 4.2 six code p0014 cam timing, dies, stalls.
2004 SES Codes P0128, P0172, P0455, P0410, P0606
The garage checked out a few of the codes and said that all values and sensors were
fine. Garage did not specify which codes they checked. Said they only checked out a
few of the codes. SES will not reset, comes right back on with the same codes...
Rattle Noise in Font End
Replaced stabilizer links. I have a rattling noise in the left front when I go over
some bumps. The shocks seem to be fine, but I don't know what is the problem...
Idle Problem With My 2003 Chevrolet
My truck dies when i turn on the a/c or heat, it's fine when it's just running, and i am also
losing some power with the buttons on the doors with the lock and unlock button, there is
no other problems but the rpm's dip way down below one when idling
Scan Code P0128 How To Repair
My service engine light is on. The dealer said the code is P0128 "Coolant Thermostat
Coolant temperature below thermostat regulating sensor. My temperature gauge reads
okay and the vehicle runs good. Is it difficult to change this myself
Chevrolet Trailblazer Dies at Idle
When i turn on my a/c and let it idle the rpm dips way low and almost stalls until i rev it up
again but if I let it sit it shuts off. Does the same thing when i turn on the heat. Aside from that
the engine is fine, but only when the A/C and heat get turned on it starts to die
Should I replace the cam actuator solenoid valve for this code on my Trailblazer.
Does the power steering pump have to be removed.
2003 Trailblazer Stalls
Check engine light ans codes P1515, P1514, P0335, P0013. Replaced throttle
TPS and cam crank position sensors.
Truck Hard To Start
After driving for a while and then shutting off my Trailblazer, it is real hard to start.
Sounds like it is flooded. Mechanic says it is the thermostat and serpentine belt.
How to Replace Air Induction Valve
Check engine light on my Chevrolet Trailblazer. Code came up for this part.. Can i
do the repair myself?
Headlight Socket Burned
The headlight on my Trailblazer burned the bulb and socket so i
replaced it. No fuses blew. Will this repair last.
Low Idle with A/C
My truck will idle very low and almost die out when turning on the
air conditioning. What can cause this problem.
Clicking in Dash
When i start my GMC Envoy, there is a clacking near the A/C controls or
maybe from the 4wd switch. A friend said it was a sensor. What could this
|I have a 2002 trailblazer.
Ignition key is stuck and will not turn back to the spot where I can remove the key.
Battery is dead also.
|The dead battery is the reason you cannot remove the
key and the ignition won't turn all the way off to the lock
position. Either get a jump or charge it or replace the
Truck Will Not Shift
After replacing the battery in my truck, the transmission acts like it is stuck in neutral.
The gauges are all bottomed out an the it dies out coming to a stop at idle.
|My 04 Chevrolet Trailblazer seems to engage the brakes when i turn.
|It sounds like you have an ABS problem. Either a bad
front speed sensor, which is part or the wheel bearing
hub, or a wiring harness problem to one of the front
sensors. Have the wiring checked first.
1992 Blazer Hesitating Badly
After my truck was sitting a long time it wont go when hitting the gas. We replaced a
lot of parts. 2005 Trailblazer driver side low beam headlight the only one working.
2004 Trailblazer Shakes And Stalls
What's wrong with my truck? When i come to a stop with the air conditioning on, it
shakes and dies out. Always when coming off the highway and slowing down.
|Hello most thrilling I write from Italy I have a chevy trailblazer 04 with 33,000 miles when I
turn the key in the first position does not work at all, the remote control does not work and
when you try to start the engine is not running. my electrician thought the ignition switch
but not sure I know some of you help thanks to all
|Yes, does sound like a bad ignition switch.
|How To Replace Crank And Cam Sensor
My 2004 Chevy has a check engine and i need to know how to replace the cam solenoid
and crank position sensor. Also, is there any relearn that needs to be done.
|On my 2007 Chevy Trailblazer 4.2 vortec code po171 comes up.
|That is a lean code. Check for vacuum leaks. Especially
around the air intake box and ducts. Also make sure the
hose on the underside of the air box on top on the
engine is in place. This is left off a lot of times when the
the box was removed for some other repair.
|I have 2004 chevy trailblazer 4.2L it's missing I need to know what's the name of the part
the spark plug sits in?
|The spark plug sits in the cylinder head. The ignition coil
sits on top of the spark plug. Ignition coils are very
common for causing a check engine light with misfire
codes. If the misfire is only at idle, you may have a bad
|I need to know if i could adj rockers.
|The rocker arms on the Chevy Trailblazer are not
adjustable. Just torque them down to the specifications.
Chevrolet Trailblazer Repair Questions
2005 GMC Envoy P0128 And P0410
My truck is stalling and running rough when coming to a stop. We replaced the coolant
temperature sensor but still have a check engine light.
GMC Envoy Codes P1400 And P0506
My GMC truck has a check engine light and codes for the emissions system cold
start reduction idle air control. The throttle was cleaned and the light went out.
Ongoing starting Problem With My Truck
Sometimes the starter will crank and times it won't. The dash lights will not
come on then will be. I have used this video to test the circuits. I replaced
the ignition switch with no help.
replaced my crank&cam sensor why does it idol and then misfire when u start to drive when idling it runs for 5/10 min normal then it cuts out coed 1345
keeps coming out what else should I check all coils are good.
Reply @mike, If this code was not there before, you need to have the "cam / crank correlation relearn" procedure done.
when I dim my head lights they go out completly.
Reply @Donald, sounds like the dimmer switch is bad. Check all fuses first. Then you are going to have to use a volt meter to test output voltage of