All times are UTC - 6 hours [ DST ]




Ask A Question Reply    Go to page 1, 2  Next
Author Message
 

contributions: 7
I'm searching for the color diagram for the multi switch. Which color wire goes to which pin.

I'm most interested in pin 1-8.

Thanks


Share on FacebookShare on DiggShare on DeliciousShare on TechnoratiShare on TumblrShare on Google+
   
Reply with quote  
* Search   
 
User avatar

contributions: 2078
Images: 37
Location: Oregon
what pins are you looking for? Turn, wiper, high beams... (it looks like you should have two seven wire connectors)
if you just want colors:
684 pink/yel
359 gry/red
880 lt blu/org
44 lt blu
385 wht/red
3 lt grn/wht
9 dk blu/wht
5 brn/yel
2 wht/lt blu
511 lt grn

these are for high beams
dk blu/org
red/yel
gry/org
red/blk


Attachments:
explorer multi switch.jpg
explorer multi switch.jpg [ 42.41 KiB | Viewed 690 times ]
explorer multi pins.jpg
explorer multi pins.jpg [ 34.35 KiB | Viewed 690 times ]
   
Reply with quote  
 

contributions: 7
1999 Ford Explorer Sport

The wires were loose and fell out. Some may have been put back in the incorrect positions. Mainly the top portion pins 1-8.

I got a replacement harness from the junkyard and the some wires don't match. The discrepancy may be my own (my brother) fault but I'm unsure.

As you can see the discrepancy on terminal 4 & 7 and the reverse of wires colors 6 & 8. The missing wire from between pin 7 & 8 (blank).

the book shows pins 1-8 but I do see the higher numbers marks

pin 1 = 511
pin 2 = 3
pin 3 = 385
pin 4 = 44
pin 5 = 2
pin 6 = 6
pin 7 = 380
pin 8 = 5
blank = 379

I have posted 4 pictures for your review. 2 in this post and another 2 below it.

harness was tested for continuity between pins. all were 100%


Attachments:
File comment: FROM THE REPAIR BOOK
img_0621.jpg
img_0621.jpg [ 57.41 KiB | Viewed 687 times ]
File comment: HARNESS
img_0623 NUMBERED_edited-1.jpg
img_0623 NUMBERED_edited-1.jpg [ 59.83 KiB | Viewed 687 times ]
   
Reply with quote  
 

contributions: 7
see some of the wires are not matching...

pin 1, 2, 3, 5 match perfectly.
4 & 7 are switched
8 empty
6 & 8 reversed


Attachments:
File comment: junkyard replacement
img_0628 NUMBERED_edited-1.jpg
img_0628 NUMBERED_edited-1.jpg [ 47.1 KiB | Viewed 687 times ]
File comment: harness on my truck
img_0626 NUMBERED_edited-1.jpg
img_0626 NUMBERED_edited-1.jpg [ 50.06 KiB | Viewed 687 times ]
   
Reply with quote  
 

contributions: 7
I'm guessing for starters. Pin 7 continuity has no match according to the book, so that might be in the wrong place.

I might have to move it to the 4 position since that has multiple matching points needed for continuity.


   
Reply with quote  
 

contributions: 7
carriedi wrote:
> what pins are you looking for? Turn, wiper, high beams... (it looks like
> you should have two seven wire connectors)
> if you just want colors:
> 684 pink/yel
> 359 gry/red
> 880 lt blu/org
> 44 lt blu
> 385 wht/red
> 3 lt grn/wht
> 9 dk blu/wht
> 5 brn/yel
> 2 wht/lt blu
> 511 lt grn
>
> these are for high beams
> dk blu/org
> red/yel
> gry/org
> red/


What about the other pin colors?


   
Reply with quote  
 
User avatar

contributions: 2078
Images: 37
Location: Oregon
how many wired connectors are in each harness connector?

yes, switch 4 and 7 by your numbering system would look to be correct.

the top picture appears to be the correct positions. If you have a trailer connector in the back of your truck you can check if the turn signals are to the correct side. If they are opposite then you need to switch the brn/yel and the drk blu/white wires.


   
Reply with quote  
 

contributions: 7
The lower harness is complete with no problems pins 9-15.

I switched 4 & 7 and all work. Light, wipers, turn, hazard, high, low.

Now 6 & 8 are hanging loose. No trailer connection to worry about.

I tested both 6 & 8 matching color to color and reversing the colors and I don't notice anything happening.

Should I just connect them?


   
Reply with quote  
Ask A Question Reply    Go to page 1, 2  Next

   Similar Topics   Author   Replies   Views   Most Recent 
New Articles View the first Bad wheel bearing, 1999 Explorer Sport

in Ford Trucks

Cari

1

1190

Thu Dec 04, 2014 5:05 am

carriedi View the latest

New Articles View the first 1999 Ford Explorer Brake pedal down

in Ford Trucks

ajhank

3

1383

Thu Feb 25, 2016 11:42 am

carriedi View the latest

New Articles View the first Ford Explorer Anti-theft problem

in Ford Trucks

Allen

1

1753

Fri Oct 02, 2015 3:01 am

carriedi View the latest

New Articles View the first Ford 2010 explorer 4.0 overheating when not accelerating

in Ford Trucks

Gildave

1

706

Mon Jul 18, 2016 8:28 pm

carriedi View the latest

New Articles View the first 2010 Ford Explorer overheating when accelerating, no heat

in Ford Trucks

csylvia02

2

1582

Wed Dec 31, 2014 8:36 pm

dhdishner View the latest

New Articles View the first 1994 explorer

in Ford Trucks

Lockemon

3

748

Sat Dec 10, 2016 12:07 pm

carriedi View the latest

New Articles View the first trailer brake and turn signals not working

in Ford Trucks

tinstar26

3

1442

Sat Nov 29, 2014 1:37 pm

tinstar26 View the latest


All times are UTC - 6 hours [ DST ]



Search for:
Jump to:  
Contact Us